Kode per zhbllokimin e telefonave 

--------------------------------------------------------------------------------

Siemens:
C25

Secret Codes

SP unlock *#0003*(secret code 8 digits)#

*#0606# shows you Secret Code, but only without SIM Card.

*#06# for checking the IMEI (International Mobile Equipment Identity)

Resets language to automatic selection : * # 0000 # then Green button

Pin Out (electrical connections)

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO




S25

SP unlock *#0003*(secret code 8 digits)#

*#0606# shows you Secret Code, but only without SIM Card.

*#06# for checking the IMEI (International Mobile Equipment Identity)

Resets language to automatic selection : * # 0000 # then Green button



S25, M35, S35, C35


SP unlock *#0003*(secret code 8 digits)#

*#0606# shows you Secret Code, but only without SIM Card.

*#06# for checking the IMEI (International Mobile Equipment Identity)

Resets language to automatic selection : * # 0000 # then Green button


Siemens S1 Secret Codes


SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

Tetris
Power on phone and enter PIN. before phone has locked onto network, F9, send own number, hit right button, hit 9. left is 2, right is 8, rotate is 5, and drop is 4.

Monitor Mode
1. Menu
2. 9 (Phone Options)
3. 7 (Phone Status)
4. Left Display Button (left MENU key)
5. 5553756
6. HangUp Button (Red HandSet key)

Now "Monitor" should appear at the bottom of the Network Options menu. Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress )

CH Channel Number
RX Signal Strength (dB)
N NCC (Color Code)
B BCC (Color Code)
CI Cell ID (in Hex)
C1+ how long before phone does forced hand over. (see RX and RXAM)
LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC
TXPWR Transmit Power (dB)
RXAM Reeceive signal strength cut-off point
TS* Time Slot Number
TA* Timing Advance. Distance from tower in Km * 2
PL* Power Level

Power Table
PL: 5 6 7 8 9 10 11 12 13 14 15
dB: 33 31 29 27 25 23 21 19 17 15 13
Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02

LF* C1 value with continuous transmisson from tower
LS* C1 Value with discontinuous tranmission from tower
QF* Bit Error Rate with continuous transmission from tower
QS* Bit Error Rate with discontinuous transmission from tower

BER (bit error rate) table
QF/QS register: 0 1 2 3 4 5 6 7
% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6

Tips and tricks

Nice Sunset in the display. Siemens S3 or younger
In the Telephone Book in the section own numbers, first position you have to type in +12022243121 (Number of the Capitol in Washington DC) and save it without a name. Then open this telephone book again do so as you like to change the number but leave the modus without changing anything. A nice Sundown will be shown in the display.

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO

Siemens S3 / S3 Secret Codes


SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

Tetris
Power on phone and enter PIN. before phone has locked onto network, F9, send own number, hit right button, hit 9. left is 2, right is 8, rotate is 5, and drop is 4.

Monitor Mode
1. Menu
2. 9 (Phone Options)
3. 7 (Phone Status)
4. Left Display Button (left MENU key)
5. 5553756
6. HangUp Button (Red HandSet key)

Now "Monitor" should appear at the bottom of the Network Options menu. Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress )

CH Channel Number
RX Signal Strength (dB)
N NCC (Color Code)
B BCC (Color Code)
CI Cell ID (in Hex)
C1+ how long before phone does forced hand over. (see RX and RXAM)
LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC
TXPWR Transmit Power (dB)
RXAM Reeceive signal strength cut-off point
TS* Time Slot Number
TA* Timing Advance. Distance from tower in Km * 2
PL* Power Level

Power Table
PL: 5 6 7 8 9 10 11 12 13 14 15
dB: 33 31 29 27 25 23 21 19 17 15 13
Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02

LF* C1 value with continuous transmisson from tower
LS* C1 Value with discontinuous tranmission from tower
QF* Bit Error Rate with continuous transmission from tower
QS* Bit Error Rate with discontinuous transmission from tower

BER (bit error rate) table
QF/QS register: 0 1 2 3 4 5 6 7
% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6

Unlock Siemens S3(Not S3 COM)
(For advanced users only)

At addresses 0D8 to 0DD the phones code is stored. To read the code swap nibbles stored at addresses from 0DA to 0DD. Error counter is at 0D9. To clear the Phone Code write at addresses from 0D8 to 0DD: 00, 00, FF, FF, FF, FF.

Siemens S3 comfort

Show IMEI code: * # 06 #

MONITOR MODE
The Siemens S3 Com series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone.

TO ACTIVATE MONITOR MODE
1. Turn the phone on.
2. Enter the PIN access code on press OK. (Only if is enabled).
3. Press Menu. (Left top button).
4. Press 9. (Phone Options).
5. Press 8. (Phone Status) (May be button 7 in some phones).
6. You may see your IMEI Number
7. Left Display Button (Top left MENU key).
8. 7684666
9. HangUp Button. (Red HandSet key).

Note: Monitor should appear now at the bottom of the Network Options menu.

MONITOR MODE TOGGLE
Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes

Tips and tricks

Nice Sunset in the display. Siemens S3 or younger
In the Telephone Book in the section own numbers, first position you have to type in +12022243121 (Number of the Capitol in Washington DC) and save it without a name. Then open this telephone book again do so as you like to change the number but leave the modus without changing anything. A nice Sundown will be shown in the display.

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO


Siemens S4 / S4 Power Secret Codes

SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

MONITOR MODE
The Siemens S4 series also haves a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone.

TO ACTIVATE MONITOR MODE
1. Menu
2. 9 (Phone Options)
3. 7 (Phone Status)
4. Left Display Button (left MENU key)
5. 7684666
6. HangUp Button (Red HandSet key)

Now "Monitor" should appear at the bottom of the Network Options menu. Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress )

Unlock Siemens S4
(For advanced users only)

At addresses 0D8 to 0DD the phones code is stored. To read the code swap nibbles stored at addresses from 0DA to 0DD. Error counter is at 0D9. To clear the Phone Code write at addresses from 0D8 to 0DD: 00, 00, FF, FF, FF, FF.

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO Siemens S25, M35, S35, C35 Secret Codes

SP unlock *#0003*(secret code 8 digits)#

*#0606# shows you a big Hexadecimal Code, but only without SIM Card.

*#06# for checking the IMEI (International Mobile Equipment Identity)

Resets language to automatic selection : * # 0000 # then Green button

S25

*#00(International prefix code of the country)# you get the language of that country (if supported)
e.g.: *#0039# switches to Italian language, *#0044# or *#001# switches to English

S35i

Fullscreen for WAP
Connected to the Internet, press twice right button (the one for recording) and all the status lines, one up of the screen and two on the bottom of the screen, WILL DISAPPEAR !!!! So, you can use the whole screen for browsing the internet !!! Press again the button the lines will appear.

Samsung
Samsung

*2767*688# = Unlocking Code
*#8999*8378# = All in one Code
*#4777*8665# = GPSR Tool
*#8999*523# = LCD Brightness
*#8999*3825523# = External Display
*#8999*377# = Errors
#*5737425# = JAVA Something{I choose 2 and it chrashed}][/b]
*#2255# = Call List

#*536961# = Java Status Code
#*536962# = Java Status Code
#*536963# = Java Status Code
#*53696# = Java Status Code

#*1200# = AFC DAC Val
#*1300# = IMEI
#*1400# = IMSI

#*2562# = FRAGE White for 15 secs than restarts.
#*2565# = Check Blocking
#*3353# = Check Code
#*3837# = FRAGE White for 15 secs than restarts.
#*3849# = FRAGE White for 15 secs than restarts.
#*3851# = FRAGE White for 15 secs than restarts.
#*3876# = FRAGE White for 15 secs than restarts.

#*7222# = Operation Typ (Class C GSM)
#*7224# = I Got !! ERROR !!
#*7252# = Oparation Typ (Class B GPRS)
#*7271# = Multi Slot (Class 1 GPRS)
#*7274# = Multi Slot (Class 4 GPRS)
#*7276# = Dunno
#*7337# = EEPROM Reset (Unlock and Resets Wap Settings)
#*2787# = CRTP ON/OFF
#*3737# = L1 Dbg data
#*5133# = L1 Dbg data
#*7288# = GPRS Attached
#*7287# = GPRS Detached
#*7666# = SrCell Data
#*7693# = Sleep Act/DeAct (Enable or Disable the Black screen after doing nothing for a while)
#*7284# = Class : B,C or GPRS
#*2256# = Calibration Info
#*2286# = Battery Data
#*2527# = GPRS Switching (set to: class 4, class 8, class 9 or class 10)
#*2679# = Copycat feature (Activate or Deactivate)
#*3940# = External loop test 9600 bps
#*4263# = Handsfree mode (Activate or Deactivate)
#*4700# = Half Rate (Activate or Deactivate)
#*7352# = BVMC Reg value
#*8462# = Sleeptime
#*2558# = Time ON
#*3370# = EFR (Activate or Deactivate)
#*3941# = External looptest 115200 bps
#*5176# = L1 Sleep
#*7462# = SIM phase
#*7983# = Voltage/Frequenci (Activate or Deactivate)
#*7986# = Voltage (Activate or Deactivate)
#*8466# = Old time
#*2255# = Call FRAGE
#*5187# = L1C2G trace (Activate or Deactivate)
#*5376# = FRAGE White for 15 secs than restarts.
#*6837# = Official Software Version
#*7524# = KCGPRS
#*7562# = LOCI GPRS
#*7638# = RLC allways open ended TBF (Activate or Deactivate)
#*7632# = Sleep mode Debug
#*7673# = Sleep mode RESET
#*2337# = Permanent Registration Beep
#*2474# = FRAGE
#*2834# = Audio Path
#*3270# = DCS support (Activate or Deactivate)
#*3282# = Data (Activate or Deactivate)
#*3476# = EGSM (Activate or Deactivate)
#*3676# = Flash volume formated
#*4760# = GSM (Activate or Deactivate)
#*4864# = Dunno doesn't work on newer versions
#*5171# = L1P1
#*5172# = L1P2
#*5173# = L1P3
#*7326# = Accessory (I got Vibrator)
#*7683# = Sleep variable (
#*7762# = SMS Brearer CS (Activate or Deactivate)
#*8465# = Time in L1
#*9795# = wtls key
#*2252# = Current CAL
#*2836# = AVDDSS Management (Activate or Deactivate)
#*3877# = Dump of SPY trace
#*7728# = RSAV done# (Everything went to standart but nothing was deleted)
#*2677# = ARM State (None or Full Rate)
*#8999*636# = Have no clue what it is, i see 20 lines
*#9999# = Software version
*#8999*8376263# = HW ver, SW ver and Build Date
*#8888# = HW version
*#8377466# = Same HW/SW version thing

*#7465625# = Check the locks
*7465625*638*Code# = Enables Network lock
#7465625*638*Code# = Disables Network lock
*7465625*782*Code# = Enables Subset lock
#7465625*782*Code# = Disables Subset lock
*7465625*77*Code# = Enables SP lock
#7465625*77*Code# = Disables SP lock
*7465625*27*Code# = Enables CP lock
#7465625*27*Code# = Disables CP lock
*7465625*746*Code# = Enables SIM lock
#7465625*746*Code# = Disables SIM lock
*7465625*228# = Activa lock ON
#7465625*228# = Activa lock OFF
*7465625*28638# = Auto Network lock ON
#7465625*28638# = Auto Network lock OFF
*7465625*28782# = Auto subset lock ON
#7465625*28782# = Auto subset lock OFF
*7465625*2877# = Auto SP lock ON
#7465625*2877# = Auto SP lock OFF
*7465625*2827# = Auto CP lock ON
#7465625*2827# = Auto CP lock OFF
*7465625*28746# = Auto SIM lock ON
#7465625*28746# = Auto SIM lock OFF

*2767*3855# = E2P Full Reset
*2767*2878# = E2P Custom Reset
*2767*927# = E2P Wap Reset
*2767*226372# = E2P Camera Reset
#*6420# = MIC Off
#*6421# = MIC On
#*6422# = MIC Data
#*6428# = MIC Measurement
#*3230# = Trace enable and DCD disable
#*3231# = Trace disable and DCD enable
#*3232# = Current Mode
#7263867# = RAM Dump (On or Off)
*2767*49927# = Germany WAP Settings
*2767*44927# = UK WAP Settings
*2767*31927# = Netherlands WAP Settings
*2767*420927# = Czech WAP Settings
*2767*43927# = Austria WAP Settings
*2767*39927# = Italy WAP Settings
*2767*33927# = France WAP Settings
*2767*351927# = Portugal WAP Settings
*2767*34927# = Spain WAP Settings
*2767*46927# = Sweden WAP Settings
*2767*380927# = Ukraine WAP Settings
*2767*7927# = Russia WAP Settings
*2767*30927# = GREECE WAP Settings
*2767*73738927# = WAP Settings Reset
*2767*49667# = Germany MMS Settings
*2767*44667# = UK MMS Settings
*2767*31667# = Netherlands MMS Settings
*2767*420667# = Czech MMS Settings
*2767*43667# = Austria MMS Settings
*2767*39667# = Italy MMS Settings
*2767*33667# = France MMS Settings
*2767*351667# = Portugal MMS Settings
*2767*34667# = Spain MMS Settings
*2767*46667# = Sweden MMS Settings
*2767*380667# = Ukraine MMS Settings
*2767*7667#. = Russia MMS Settings
*2767*30667# = GREECE MMS Settings
*335# = Delete all MMS Messages
*663867# = Dump Mm file
#*536961# = WAPSAR enable / HTTP disable
#*536962# = WAPSAR disable / HTTP enable
#*536963# = Serial eable / Others disable
#*53696# = Java Download Mode
#*5663351# = Wap Model ID [Your Model]
#*5663352# = Wap Model ID [SEC-SGHXXXX/1.0]
#*566335# = Wap Model ID [SEC-SGHXXXX/1.0]
*2767*66335# = Check on which model it is
*2767*7100# = SEC-SGHS100/1.0
*2767*8200# = SEC-SGHV200/1.0
*2767*7300# = SEC-SGHS300/1.0
*2767*7650# = Nokia7650/1.0
*2767*2877368# = Reset WAP Model ID to standart

NOKIA

Kodet per Nokia 3210 - 5110 - 6110

1.Per te mesuar IMEI e telefonit tuaj formoni * # 0 6 #

2.Per te mesuar versionin e softwarit te telefonit tuaj formoni numrin * # 0 0 0 0 #

3.Per te mesuar daten e prodhimit,numrine serise, dhe daten e fundit te riparimit (nese ka) te telefonit tuaj formoni numrin qe vijon * # 9 2 7 0 2 6 8 9 #

4.Per te rritur kualitetin e kerkimit( por shkurton jeten e baterise) formoni * 3 3 7 0 # . Per ta mbyllur # 3 3 7 0 #

5.Per te ulur kualitetin e kerkimit( rritet jeta e baterise) formoni * 4 7 2 0 # . Per ta mbyllur formoni # 4 7 2 0 #


Kodet per Nokia 6150

1.Per te mesuar IMEI e telefonit tuaj formoni * # 0 6 #

2.Per te mesuar versionin e softwarit te telefonit tuaj formoni numrin * # 0 0 0 0 #

3. *#746025625# - [*#sim0clock#]
Nese deshironi mund ta mbyllni Sim Clock e cila zvogelon humbjen e energjise se baterise. Nuk punon ne versionin 4.59 .

4. *#92702689 - [*#var0anty#]
Mund te mesoni kodin e garanitise te celularit tuaj... Mund te shikoni menune me poshte..

Menuja:

1. Shikoni serine e telefonit

2. Shikoni datene prodhimit (psh. 0997)

3. Shikoni daten e fundit te modifikimit

4. Te gjith numerat,pictures,zilet ne telefonin tuaj mundi transferoni ne nje telefon tjeter.

*3370# mbasi te jete mbyllur telefoni, EFR eshte ne gjendje aktife, e cila ben qe te dalin tingujt EFR me te qarte por harxhon baterine me shume se sa normalja. Jep 5% me shume nga koha e foljes.
#3370# mbasi te jete fikur telefoni, EFR mbyllet.

*4720# mbasi te jete mbyllur telefoni, HRC eshte ne gjendje aktife,kjo ben qe zerate HRC te dalin m?me pak kaulitet,mirepo e harxhon me pak baterine nga normalja.
#4720# mbasi te ejte mbyllur telefoni,e mbyll HRC ..

Nje rruge interesante per ta mbyllur telefonin.

Ne disa telefona jep mesazh te gabuar,atehere nuk mund ta perdorni kete kod.

Shkoni ne menune (Calendar) (menu -
Make note / reminder
Shkruani dicka te kutia
Shtypni butonin e fshirjes derisa te keni fshire cdo gje qe patet shkruar.
Pastaj shtypni butonin back..
Shtypni 0.
Futni 4 numera(1234 per shembull)
Shtypni dy here poshte butonin OK
Tani futni 6 numera dhe shtypni butonin e gjelber "Butoni i kerkimit".
Prisni pak dhe telefoni do te jape sinjal dhe papritmas do te fiket...
Nuk punon ne versionet V5.20 20-09-99 NSM-1


Kodet per Nokia 8810


1.Per te mesuar IMEI e telefonit tuaj formoni * # 0 6 #

2.Per te mesuar versionin e softwarit te telefonit tuaj formoni numrin * # 0 0 0 0 #


3. *#746025625# - [*#sim0clock#]
Nese deshironi mund ta mbyllni Sim Clock e cila zvogelon humbjen e energjise se baterise. Nuk punon ne versionin 4.59


4. *#92702689 - [*#var0anty#]
Mund te mesoni kodin e garanitise te celularit tuaj... Mund te shikoni menune me poshte..

Menuja:

1. Shikoni serine e telefonit

2. Shikoni datene prodhimit (psh. 0997)

3. Shikoni daten e fundit te modifikimit

4. Te gjith numerat,pictures,zilet ne telefonin tuaj mundi transferoni ne nje telefon tjeter.


*3370# mbasi te jete mbyllur telefoni, EFR eshte ne gjendje aktife, e cila ben qe te dalin tingujt EFR me te qarte por harxhon baterine me shume se sa normalja. Jep 5% me shume nga koha e foljes.
#3370# mbasi te jete fikur telefoni, EFR mbyllet.

*4720# mbasi te jete mbyllur telefoni, HRC eshte ne gjendje aktife,kjo ben qe zerate HRC te dalin m?me pak kaulitet,mirepo e harxhon me pak baterine nga normalja.
#4720# mbasi te ejte mbyllur telefoni,e mbyll HRC


NOKIA

IMEI number: * # 0 6 #
Software version: * # 0 0 0 0 # or * # 9 9 9 9 #
Simlock info: * # 9 2 7 0 2 6 8 9 #
Enhanced Full Rate: * 3 3 7 0 # [ # 3 3 7 0 # off]
Half Rate: * 4 7 2 0 #
Provider lock status: # p w + 1 2 3 4 5 6 7 8 9 0 + 1
Network lock status: # p w + 1 2 3 4 5 6 7 8 9 0 + 2
Provider lock status: # p w + 1 2 3 4 5 6 7 8 9 0 + 3
SimCard lock status: # p w + 1 2 3 4 5 6 7 8 9 0 + 4


Oxygen Ringtone Workshop for Nokia phones

Works under Microsoft Windows'95, '98, Windows NT, Windows ME, Windows 2000 and Windows XP operating systems family and supports FBUS cable or Infrared connection. This program is freeware.
DL:


http://www.oxygensoftware.com/downlo...p?File=ORW.zip

Codet e celularit Sony

Kodet e Sony CMD-Z 1:

formo *#06# te shikosh IMEI

versioni Software dhe daten e prodhimit : Press # 8377466 # (#version#)

Sony CMDX 1000

tregon Software date : Remove your SIM Card, dhe pastaj : * # 06 #
dhe pastaj press:
[left softkey]
To enter Monitor Mode on Netvork Option menu:
Menu
9 (Phone Options)
7 (Phone Status)
[Left Display Button] (left MENU key) 7684666 [HangUp Button] (Red HandSet key)

Some characters explained

* activate
** register and activate
*# check status
# unregister
## unregister and deactivate

Call barring
**33*code# Activate barr all outgoing calls (for code see "Safety" above)
#33*code# Deactivate barr all outgoing calls
*#33# Check status of barr all outgoing calls
**330*code# Activate barr all calls
#330*code# Deactivate barr all calls
*#330*code# Check status of barr all calls
**331*code# Activate barr all outgoing international calls
#331*code# Deactivate barr all outgoing international calls
*#331*code# Check status of barr all outgoing international calls
**332*code# Activate barr all outgoing international calls except home country
#332*code# Deactivate barr all outgoing international calls except home country
*#332*code# Check status of barr all outgoing international calls except home country
**333*code# Activate barr all outgoing calls
#333*code#

Kodet per SAMSUNG SH600:

*#06# -> IMEI
*#9999# -> Versioni i Software
*#0837# -> Version i Software (per te dhene prodhimin)
*#0001# -> Seria
*#9125# -> qesh kur ben sarzh

*#9998*228# ->gjendjae baterise
*#9998*246# -> gjendja e programit
*#9998*289# -> per te rregulluar gjendjen e alarmit
*#9998*324# -> ekrani i pare
*#9998*364# -> qeni time !!!
*#9998*377# -> gabimimi EEPROM .Futeni madhesin e butonit. Cancel dhe ok.
*#9998*427# -> per te gjetur qenin time (per zotin se ca do te thote qeni time nuk e di)
*#9998*523# -> Kontrasiti i ekranit LCD - vetem versionin me G60RL01W
*#9998*544# -> kerkimi i shpejtesise
*#9998*636# -> gjendja e memories
*#9998*746# -> gjatesia e file-it SIM
*#9998*778# -> Tblojae servisit SIM
*#9998*785# -> Gabimet RTK - nese shtyp ok, telefoni kycet, B gabim ne memorien informative.

*#9998*786# -> Run, fund, UP, fund



Kodet per SAGEM :

*# Komandat
*#06# numri i IMEI
*#30# Per te pare ID qe ka ardhur
*#31# -//- ID qe ka ikur
*#33# ben inaktife butonin e thirrjes
*#35# ben aktife -//-
*#43# vonesae thirrjes
*#100# ju tregon numrin tuaj te telefonit
*#101# DHLRU1 ?me falni po kete nuk e di se cfare eshte?
*#102# informata e dergimit
*#103# Koha qe jeni
*#147#Numri i fundit qe ju ka marrur
*#1345# Kjo eshte per te pare se sa kohe dhe sa kredi ja kane marre bisedimet .

Cfare eshte numri IMEI?:

IMEI eshte numri i serise qe ka telefoni juaj .Nese telefoni juaj eshte i vjedhur ne saje te ketij numri musn te behet e ditur. Biles nese telefoni juaj eshte vjedhur jashte shtetit ne baze te ketij numri mesohet se ne cfare qyeteti dhe cafre karte eshte duke u perdorur ne keto momente. Hapeni telefonin tuaj formoni kodet * # 0 6 # . Numri qe ka dale eshte IMEI juaj. Kur mund te ju hyje juve ne pune kjo? Le te themi se jeni duke blere nje telefon second hand .(biles mund te ju shesin nje telefon te vjedhur duke ua treguar ate juve sikur eshte prodhim 0).
Kpntrolloni numrin serise qe eshte ne kutine telefonit qe ju ka dhene shitesi me numrin qe gjetem.
Nese numrat nuk jane te njejte menjehere njoftoni policine pasi ai telefone shte i vjedhur ..

vllai ca i boke copy paste ti PP po megjithse qekan interesante si kom hy ndonjeher bots se celularve .. vetem sa me fol e maj 

 

 Postimi origjinal është bërë nga Pogradecari 

NOKIAOxygen Ringtone Workshop for Nokia phones

Works under Microsoft Windows'95, '98, Windows NT, Windows ME, Windows 2000 and Windows XP operating systems family and supports FBUS cable or Infrared connection. This program is freeware.
DL:


http://www.oxygensoftware.com/downlo...p?File=ORW.zip

kjo faqe nuk po bon, arsyeja: "Document not found on Oxygen Software site."

Kesmet se shpejti do ta bejme jackas per nje jave e ke gati pa merak.

O igli kush i ben copy paste shikoji njehere pasaj fol.

A mund te zhbllokohet ky lloj telefoni : 3 skype phone amoi wp-s1 ?

 

 Postimi origjinal është bërë nga T-Ghost 

A mund te zhbllokohet ky lloj telefoni : 3 skype phone amoi wp-s1 ?

Do mundohem njehere pasaj do te kthe pergjigje.

 

 Postimi origjinal është bërë nga Pogradecari 

Do mundohem njehere pasaj do te kthe pergjigje.

Faleminderit per interesimin... Po pres...